Our Customer Service team are always on hand to help, but for generic queries please navigate our FAQ tabs below:
The information contained within this website is for guidance only, for further system specific advice please call A-Gas directly.
A. All of our non-bulk Refrigeration cylinders are fitted with a 3/4’’ 14 NPT Valve. For Industrial Gas cylinders, please refer to the Australian Standard AS2473 for valve fittings
A. Due to its flammability, R32 cylinders are fitted with a 3/4” 14 NPT Reverse Left-handed Thread valve. Fitting adaptors are available from your Refrigerant retailer.
A. For all cylinders, the initial test date is also the manufactured date. This can be found on the rear or side of the valve guard for welded steel cylinders, or on the shoulder of an Industrial Gas/Torpedo cylinder. This test date is valid for 10 years and if it has expired, a retest date can be found on the edge of the valve guard towards the front of the cylinder or on the shoulder for an Industrial/Torpedo cylinder.
A. Statutory Regulations require refrigerant welded steel gas cylinders to be inspected and tested every ten (10) years. Therefore gas cylinders that are “out-of-test date” cannot be re-filled until re-tested, re-stamped & re-certified by a Licenced Gas Cylinder Test Station. An important distinction is refrigerant cylinders that are re-filled prior to the due 10 year re-test date can still be used in circulation until the refrigerant gas is completely decanted. Should Pump-down or reclaim cylinders be “Out of Test”, the cylinder must not be used for reclamation filling by the licenced contractor & should be returned to A-Gas.
Reclaim cylinders are used in the recovery of used refrigerant. They have specialised dual outlet valves allowing reclaim of refrigerant by pump or push/pull. Pump-down cylinders are used in the recovery of used refrigerant to allow servicing on equipment. They must not be returned to A-Gas full. Each Pump-down cylinder returned to A-Gas is inspected internally after being thoroughly cleaned of all oil and contaminants. R32 Reclaim cylinders have a higher pressure rating than standard Reclaim cylinders, suitable for R32’s higher pressure. Using a standard Reclaim cylinder, will cause the cylinders’ safety relief valve to open. Some important practices to be followed in the use of Reclaim and Pump-down cylinders:
- Reclaim and Pump down cylinders should never be used to reclaim ammonia (R717).
- Reclaim and Pump down cylinders should not be used to reclaim flammable hydrocarbon refrigerants such as R600a, R290, R1270.
- Reclaim and Pump down cylinders should never be filled above the specified maximum fill weight.
- Always apply the valve caps after reclaiming refrigerant into a cylinder.
- Best practice suggests that refrigerants should not be mixed.
For our Retail Branch customers, if you have any concerns or issues about an A-Gas cylinder and/or our product, please call one of our friendly Customer Service representatives on (03) 9368 9222 or Toll Free on 1800 002 427. Alternatively, you can chose email us at firstname.lastname@example.org For end users, please contact the retailer from where the cylinder or product was purchased for further assistance.
A-Gas now has an online system for arranging the pickup of empty cylinders from your branch outlet. Just click on the link, https://clientau.agas.com and log in with your password to get started. If you are unsure of the login details for your branch or require further assistance in the return of your empty cylinder, please call (03) 9368 9222 or Toll Free on 1800 002 427. For end users, please return your cylinders to the retail outlet from where the cylinder was purchased.
Shipper formats have been designed by A-Gas to maximise the amount of cylinders that can be shipped to you on a Standard Australian Pallet 1165mm x 1165. Importantly, it also allows us to transport the cylinders in the safest possible manner, ensuring the cylinders are secured correctly.
- Shipper 1: 2 Layers of 20 Small* A-Gas cylinders = 40 cylinders in total
- Shipper 2: 2 Layers of 12 Medium* A-Gas cylinders = 24 cylinders in total
- Shipper 3: 1 Layer of 9 Large* A-Gas Cylinders = 9 cylinders in total
- Shipper 4: 2 Layers of cylinders (1st layer 20xSmall + 2nd Layer 12xMedium) = 32 cylinders in total
- Shipper 5: 2 Layers of cylinders (1st layer 3xLarge + 12xSmall + 2nd Layer 12xSmall) = 27 cylinders in total
- Shipper 6: 2 Layers of cylinders (1st layer 3xLarge + 12xSmall + 2nd Layer 9xMedium) = 24 cylinders in total
- Shipper 7: 2 layers of cylinders (1st layer 3xLarge + 9xMedium + 2nd Layer 9xMedium) = 21 cylinders in total
*Small = 10kg to 12kg range
*Medium = 16kg to 22kg range
*Large = 50kg to 65kg range
Mixed Shippers containing Refrigerant and Industrial Torpedoes
- Shipper 1: 27 x E size Industrial cylinders
- Shipper 2: 36 x D size Industrial cylinders
- Shipper 3: 14 x E size + 15 x D size Industrial cylinders
- Shipper 4: 9 x E size Industrial cylinders + 24 x Small Refrigerant cylinders
- Shipper 5: 9 x E size Industrial cylinders + 12 x Small Refrigerant + 6 x Medium Refrigerant cylinders
- Shipper 6: 9 x E size Industrial cylinders + 12 x medium Refrigerant cylinders
- Shipper 7:11 x D size Industrial cylinders + 24 x Small Refrigerant cylinders
- Shipper 8:11 x D size Industrial cylinders + 12 x Small Refrigerant + 6 x Medium Refrigerant cylinders
- Shipper 9:11 x D size Industrial cylinders + 12 x medium Refrigerant cylinders
- Shipper 10:4 x D size + 5 x E size Industrial cylinders + 24 x Small Refrigerant cylinders
- Shipper 11:4 x D size + 5 x E size Industrial cylinders+ 12 x Small Refrigerant + 6 x Medium
Shipper 12: 4 x D size + 5 x E size Industrial cylinders + 12 x medium Refrigerant cylinders
Whatever you need to know about halon, we can help. Take a look at our frequently asked questions below. If you can’t find the information you are looking for, contact the A‑Gas team.
Halon is a fire suppressant agent found in both Fire Suppression Systems (Halon 1301) and in hand held Fire Extinguishers (Halon 1211). This is the most effective extinguishing agent available. Halon is a clean agent, which means it leaves no residue when used, so it causes no damage to your property.
The use of Halon is not banned, but rather the manufacturing of Halon globally, because of its Ozone Depleting properties. In 1987 the Montreal Protocol found Halon was damaging the environment.
Halon is still used in many applications. From protecting computer rooms throughout the electronics industry, to numerous military applications on ships and even on commercial aircraft, Halon is an integral and unparalleled fire-extinguishing agent. Halon 1211 fire extinguishers play a vital role in protecting peoples’ lives, as well as, property; including homes, automobiles and boats.
Contrary to popular belief, Halon does not remove oxygen from the air, but rather reacts with all elements of a fire. When Halon is discharged, it breaks the chemical chain reaction. This accounts for most of its fire fighting properties. The other properties come from the cooling effect of the expanding gas. Because of this, Halon can be safely used in an occupied space.
Fire Suppression System Agents:
- Halon 1301
- Halon 2402
Fire Extinguisher Streaming Agents:
- Halon 1211
- Halotron® 1
More information about each product can be found on our US website here.
A‑Gas can also help you dispose of your Halon. Occasionally, owners of ozone depleting chemicals may select destruction as a preferable option, especially if their corporate policies require permanent disposal of all ODS’s (Ozone Depleting Substances), Class 1 CFC’s and Halon. A‑Gas stands ready to accept these unwanted agents for destruction. This program is located in Bowling Green, Ohio and can achieve destruction efficiencies up to 99.9999%.
Absolutely you can buy used Halon. But when you buy a system container of Halon which has not been recycled and/or laboratory tested, you cannot be assured of what is in it. A‑Gas takes great pride in selling only recycled and laboratory certified products. Always demand laboratory certifications for each tank and/or cylinder containing Halon.
Clean agents are non-conductive, non-corrosive, and do not leave behind a residue. They are most often used in systems that protect irreplaceable or high value products such as data centers, museums, power plants, etc.